Service
Whirlpool gas dryer igniter and valve repair
A gas dryer that tumbles cold has a short, specific list: the igniter, the flame sensor, the gas valve coils and the safety devices around them. The failure is often intermittent — it lights on the third attempt, then on the fifth, then not at all — and an intermittent gas appliance is not something to live with.
- From $89 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
Before you read on
What this job costs and how it is agreed
A starting figure, not a quote. What moves it is the model, how the unit is built in and which part it needs — settled after the on-site diagnostic.
Starts at
from $175
After a diagnostic from $89, which comes off the bill when you go ahead.
or call (305) 363-7702
Diagnostic
From $89, credited to the repair
The price
In writing, before anything is opened
Warranty
On the labor we performed
On the visit
How this visit actually goes
The same order every time, so nothing is opened and nothing is charged before you have seen the figure and said yes.
-
01
Watch it try to light
The igniter glowing without the valve opening, and the valve opening without a flame holding, are two different repairs and they are visible in ten seconds.
-
02
Test the flame sensor
It has to be closed cold for the igniter to receive power. This is the part that gets missed and it is the cheapest one in the group.
-
03
Test the valve coils
Resistance on each, and a check that they hold once open. Coils fail warm, which is why the machine works for the first load of the day.
-
04
Check the airflow while it is apart
Restricted venting overheats this whole assembly and shortens everything in it.
-
05
Leak-test and document
Every joint that was disturbed, tested, and the result recorded.
Applies to
The Whirlpool units we carry this work out on
-
Vented electric · vented gas · compact heat pump · HybridCare · laundry tower Whirlpool dryer repair in Miami
Whirlpool publishes 114 pages on the dryer with 55 of them code pages, another 47 on the compact heat pump machine, 35 on the HybridCare ventless dryer, and 92 more of general dryer material — and that is before the laundry tower and the all-in-one branches, which have their own. The published code set runs wide: E1, E2, E3, F01 and F02, the F1 and F2 families, F20 through F31, F70 through F78, FCE1, Loc, PF, and one that no other appliance has — AF, which Whirlpool documents as Check Vent. That single code is the most useful thing this make publishes, because in South Florida a restricted vent is the leading cause of a dryer that has stopped drying and the leading fire risk in the room.
- Vented electric and gas, plus ventless heat pump and HybridCare condensing machines
- 55 published code pages on the vented dryer alone, including AF or Check Vent
- A ventless machine has no duct to blame — the condenser and its drain replace it
In more detail
About Whirlpool gas dryer igniter and valve repair
An intermittent flame is not something to live with
The sequence is short and it is worth knowing: the igniter glows, the flame sensor sees it is hot, the valve coils open, the gas lights, the sensor closes and the igniter goes out. Any one of those four failing produces the same complaint — a dryer that tumbles cold, sometimes. The pattern owners describe is the giveaway: it lights on the third attempt, then the fifth, then not at all. That is a circuit degrading rather than a part that has died, and on a gas appliance it gets fixed now rather than watched.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards
Before you book
Questions about Whirlpool gas dryer igniter and valve repair
Can I keep using it while it still lights sometimes?
We would rather you did not, and never overnight or while the unit is empty. A gas appliance that is not igniting reliably is not a convenience problem.
Do you leak-test the connection afterwards?
Every time, and the result is written down and left with you. Anything that involves disconnecting a gas line ends with a test, not with a sniff.
Can I run it while I wait for the appointment?
We would rather you did not run it unattended. If you must use it, stay in the unit, and stop entirely if you smell gas at any point.
Where we do it
Across Miami-Dade, Broward, and Palm Beach
Same terms everywhere we go: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
Neighborhoods people ask for by name